M3

Touch screen display Unit for 2 probes or scales


Multifunctionnal display unit for 2 probes

 

 


     

    The M3 is the last generation tool for dimensional control from 1 or 2 air gages, probes or scales.

    Several version are available allowing you to connect :

    - Inductive probes (Metro, Tesa compatible (example Tesa GT21) and Mahr (example Mahr P2004M)

    - Air gages from any brand

    - Incremental probes (Heidenhain (example Heidenhain MT101), Magnecale DK with an adaptor and Mitutoyo LG with an adaptor)

    - Linear scales (Heidenhain, Magnescale)

     

     

    Thanks to is user friendly interface and its general simplicity the M3 is a device that will be immediately adopted by every operator. The 4''3 resistive touch screen display can be used with gloves.

     

    This digital readout has several means of communication, USB and RS232 to remote control the device and/or send the measurements to an external system.

     

 

     

    Its housing machined in a solid aluminium block offers to the M3 an incomparable robustness even when use in the most severe industrial environments.

 

 

  • 2 measurement configurations (2 characteristics)
  • Different display modes with 1 or 2 measurements, with or without tolerances.
  • Tolerance limits and control limits (Warnings).
  • Absolute or relative measurement
  • Direct or dynamic measurement (Min, Max, Max-Min , Average, Median)
  • USB communication "virtual keyboard"
  • Modbus-RTU or ASCII Communication on RS232
  • Sorting by classes of size, up to 16 classes by characteristic
  • Possibility to connect an optionnal I/O module with 8 optocoupled I/O.
  • Possibility to connect a multi-function footswitch (measurement transfert, calibration etc...)
  • Optionnal external module for temperature compensation from PT100 sensor or Type K thermocouple.
  • Easy to use and reliable

M3 Display unit for measuring probes

 

Touch screen display

 

The M3 is equipped with a nice 4''3 colour touch screen display which allows an easy configuration thanks to its user friendly interface

The measurement is displayed digitally and with several types of bargraph.

 

 

FUNCTIONS

 

Many functions and measurement mode can be selected through the keyboard:

 

  • Tolerance limits, Control limits (warnings) Dimension of the master piece (reference piece) .
  • Calculation formula (C1, C2, -C1, -C2, C1+C2, C1-C2, -C1+C2, -C1-C2, 3 points diameter)
  • Calibration
  • Different display modes with 1 or 2 characteristics displayed
  • Direct or dynamic measurement (Max, Min, Max-Min, Average, Median)
  • Absolute or relative measurement
  • Sorting by classes of size, up to 16 classes by characteristic
  • Measurement direction inversion
  • Possibility to lock selected functions with a password
  • Display resolution (from 2 to 5 decimals)
  • M-Bus connector for the optionnal connection of a module with 8 input/outputs (go, nogo, preset, send measurement etc...)
  • Metric (µm or mm) or imperial measurements (inches)
  • Selection between 2 measurement configurations (2 characteristics)
  • Automatic change of program by moving the probe
  • Different languages installed. New language can be installed upon request

 

USB Connection

 

The M3 is fitted with a mini-USB connector with 2 functions :

1. Power supply through a wall mounted transformer. This transformer supplies a regulated 5V/1A DC voltage.
2. Measurement transmission. If you connect your M3 to a PC, the PC will detect and install automatically the M3 as a standard USB keyboard with the standard drivers of your operating system (Windows, Mac OS etc..). When you will send the measurement, the value will be writting on your PC screen where your cursor is, in the same way as it would have been typed with a keyboard.
No need to install any specific driver or software.

 

 

RS 232 INTERFACE

 

The RS232 interface allows to monitor and configure all the M3's functions through ASCII commands or MODBUS-RTU

 

GRAPHICAL INTERFACE


The M3 is very easy to configure and to use thank to its user friendly interface :


Display with needle indicator


1 characteristic display with control limits (Warnings)


2 characteristics display


Icon desktop (Configuration menu)


Configuration window


Display mode without tolerances and direct access to preset modification

 

3D view (Heidenhain Version)


The M3 is fitted with 2 probes inputs, 1 RS232 connector, 1 USB connector for power supply and/or communication, 1 multifunctionnal footswitch input, 1 M-Bus connector for the optionnal I/O module and 1 On/Off Switch:

 

OPTIONNAL I/O MODULE

 

 

As an option, it is possible to connect a M-Bus I/O module fitted with 8 optocoupled inputs/outputs.
M-Bus MB-IO

Available functions :
- Part 1 or 2 : Go/NoGo
- Calibration/Preset
- Start dynamic measurement
- Measurement transfert
- Zero
- Switch from part 1 to part 2
- Stop

 

APPLICATION EXAMPLE

 


Measurement of an 9.56mm internal diameter using an air probe (air plug gage) diretly connected on the M3 display.
Metro can supply a full air gage solution including display and the air probe.

 


Retrofit of a gauging fixture that was mounted with needle indicators on a 100% sorting working place:
Out-of-round (Max-Min) measurement on 2 points of a cylindrical part. Start measurement with a footswitch.
Customer benefit : Accuracy increased (1/10th of Micron), instantaneous reading of the 2 characteristics without the risk of wrong reading of the needles. Measurement transmission to a central SPC/ERP software. Significant time saved on this control place.

 


Mesurement of diameter in 3 points

 


Measurement of very small watch parts. Here the M3 is connected with a Heidenhain SPECTO probe, mounted on a Sylvac PS15 measuring bench.

 


Communication between a M3 display and a Proface PLC with the Modbus RTU protocol. The HMI from Proface has been programmed with differents buttons and indicators allowing to control and bring back informations from the M3. This Proface example can be downloaded from here

 


Retrofit of a small manual milling machine. Installation of 2 Heidenhain linear scales on the machine, connected to a M3 display with the double bargraph display mode, allowing to see both axis.

 


 


Internal diameter measurements on 2 different parts. Here the M3 displays only 1 characteristic. When the operator move a probe, the corresponding measurement appears on the screen. This functionnality allows to use only 1 display for 2 parts, and the operator has not to touch the display or change parameters for switching the part. A footswitch can be connect for preseting or to transfert the data to a computer.

 


M3 displays are not only compatible with the entire Heidenhain's range of probes and scale(Certo, MT12, MT25, MT101, Specto...) but it offers a great flexibility and a wide panel of functions with a user friendly interface.

Item references

 

Item Reference
Display M3 with 2 inputs for TTL probes (Heidenhain, Magnescale Mitutoyo) 13000
Display M3 with 2 inputs for inductive probes (Metro) 13010
Display M3 with 2 inputs for inductive probes (Tesa) 1301T
Display M3 with 2 inputs for inductive probes (Mahr) 1301M
Display M3 with 2 inputs for Heidenhain probes with a sinewave 11µA or 1Vpp signal 13020
Adapter cable to connect Mitutoyo probes LG series 24061
Cable with Digimatic output for Mux and Mitutoyo DP1 printer 18193
RS232 communication cable to P.C. 45160
Adapter cable for Magnescale probe 24062
Adapter cable for Heidenhain probe with the round M23/11µA connector 84100
Multifunctional footswitch 18020

Options

 

MB-IO module : (ref MB-IO)

 

This M-Bus module is fitted with 8 input/outputs isolated with optocouplers allowing to get additionnal functionnalities, for example : output for Go/noGo, input for preset or start dynamic measurement... The M-Bus modules are mounted on an aluminium profile allowing to mount them on a standard DIN rail. More information on this page : M-BUS

Multifunctionnal footswitch : (ref 18020 )

 

This footswitch with a robust construction can be configured in different ways : preset, measurement transmission, start dynamic measurement etc...

M-Bus cable for M3 : (ref 81213-1.5 )

 

This cable allows to connect the compatible M-Bus modules (MB-IO, MB-RL and MB-TP) on a M3 display unit (MB-IO, MB-RL and MB-TP)

Magnescale probe adapter for M2/M3 TTL : (ref 24062 )

 

This cable allows to connect 1 Magnescale probe on a M2 (ref 15000)/M3 (ref 13000) display. It integrate an electronic board that manages the error signal form the Magnescale probes.

Heidenhain M23/11µA to D-SUB 15 adapter for M2/M3 11µA/1Vpp : (ref 84100 )

 

This cable allows to connect 1 Heidenhain probe like MT12 or MT25 with the round M23 connector on a M2 (ref 15020)/M3 (ref 13020) display.

Mitutoyo LG adapter for M2/M3 TTL : (ref 24061 )

 

This cable allows to connect 1 Mitutoyo probe on a M2 (ref 15000)/M3 (ref 13000) display.

RS232 communication cable: (ref 45160 )

 

This cable allows to connect a M2 /M3 display to a computer.

RS232 to Digimatic communication cable: (ref 18193 )

 

This cable allows to connect a M2 /M3 display to a Multiplexer Mux from Metro.

RS232 to USB communication cable: (ref 45173 )

 

This cable allows a M2 /M3 display to communicate with a computer. It creates a virtual COM port on the computer. It is delivered with a driver on a CD.

 

Related products